DMC Analog Resistive Touchscreen ATP/AST Series Especificações

SpecificationG150XG01 V3 incl. Touch - 4W Content: (Mechanical Drawing Appendix A: Specification of TFT G150XG01 V3Appendix B: Specifica

G150XG01 V3 rev 1.0 8/28 Note 6: Definition of response time: The output signals of photo detector are measured when the input signals are cha

G150XG01 V3 rev 1.0 9/28 3. Functional Block Diagram The following diagram shows the functional block of the 15 inch color TFT/LCD module:

G150XG01 V3 rev 1.0 10/28 4. Absolute Maximum Ratings 4.1 Absolute Ratings of TFT LCD Module Item Symbol Min Max Unit Logic/LCD Drive Vol

G150XG01 V3 rev 1.0 11/28 5. Electrical Characteristics 5.1 TFT LCD Module 5.1.1 Power Specification Symbol Parameter Min Typ Max Units Re

G150XG01 V3 rev 1.0 12/28 5.1.2 Signal Electrical Characteristics Input signals shall be low or Hi-Z state when VDD is off. Note: LVDS Signal

G150XG01 V3 rev 1.0 13/28 5.2 Backlight Unit 5.2.1 Parameter guideline for LED Following characteristics are measured under stable condition us

G150XG01 V3 rev 1.0 14/28 6. Signal Characteristic 6.1 Pixel Format Image Following figure shows the relationship between input signal and LCD

G150XG01 V3 rev 1.0 15/28 6.3 Signal Description The module using a pair of LVDS receiver SN75LVDS82(Texas Instruments) or compatible. LVDS is

G150XG01 V3 rev 1.0 16/28 6.4 The Input Data Format 6.4.1 SEL68 SEL68 = ”High” or “NC” for 6 bits LVDS Input SEL68 = “Low” for 8 bits LVDS In

G150XG01 V3 rev 1.0 17/28 B7 B6 B5 B4 B3 B2 B1 B0 Blue Data 7 Blue Data 6 Blue Data 5 Blue Data 4 Blue Data 3 Blue Data 2 Blue Data 1 Blue D

252 ±0,3 ODT 328 ±0,3 ODT 309 VAT 233 VAT 305 AAT 229 AAT 80 ±1 0,75 ±0,5 304,10 AAD 228,10 AAD Contact 14,74 (max. 15,53) 326,50 ±0,5 ODD

G150XG01 V3 rev 1.0 18/28 6.5 Interface Timing 6.5.1 Timing Characteristics Signal Parameter Symbol Min. Typ. Max. Unit Clock Timing

G150XG01 V3 rev 1.0 19/28 6.6 Power ON/OFF Sequence VDD power and LED on/off sequence is as below. Interface signals are also shown in the cha

G150XG01 V3 rev 1.0 20/28 the power when you plug the cable into the input connector or pull the cable out of the connector. Data Modul AG - ww

G150XG01 V3 rev 1.0 21/28 7. Connector & Pin Assignment Physical interface is described as for the connector on module. These connectors ar

G150XG01 V3 rev 1.0 22/28 7.1.1 Connector Illustration SEL68 Data Modul AG - www.data-modul.com23

G150XG01 V3 rev 1.0 23/28 7.2 LED Backlight Unit: LED Driver Connector Connector Name / Designation LED Connector Manufacturer E&T or co

G150XG01 V3 rev 1.0 24/28 8. Reliability Test Criteria Items Required Condition Note Temperature Humidity Bias 5080%,300 hours High Tempera

G150XG01 V3 rev 1.0 25/28 9. Mechanical Characteristics 9.1 LCM Outline Dimension (Front View) Data Modul AG - www.data-modul.com26

G150XG01 V3 rev 1.0 26/28 9.2 LCM Outline Dimension (Rear View) Data Modul AG - www.data-modul.com27

G150XG01 V3 rev 1.0 27/28 10. Label and Packaging 10.1 Shipping Label (on the rear side of TFT-LCD display) 10.2 Carton Package Max capacity

G150XG01 V3 rev 1.0 1/28 ( ) Preliminary Specifications

G150XG01 V3 rev 1.0 28/28 11 Safety 11.1 Sharp Edge Requirements There will be no sharp edges or comers on the display assembly that could caus

Data Modul AG - www.data-modul.com SpecificationAST/ATP Series Revision 11 Version March 23, 2010

2 Rev. 11©1999 - 2010 DMC Co., Ltd. Table of Contents 1. Product Specifications ...

3 Rev. 11©1999 - 2010 DMC Co., Ltd. 1. Product Specifications 1-1. Product Applicable § This specification is applied to the analog resistive touc

4 Rev. 11©1999 - 2010 DMC Co., Ltd. 1-6. Appearance § Scratch, dust (W = width, L = length, D = average diameter = (longest + shortest) /2) Item

5 Rev. 11©1999 - 2010 DMC Co., Ltd. 2. Testing Regulation 2-1. Testing Regulation § If the regulation is not specified, the test is performed unde

2-4. Electrical Characteristics § Terminal Resistance Test Condition: Top and bottom electrodes are measured at the terminal. Judgement: Must

7 Rev. 11©1999 - 2010 DMC Co., Ltd. 3. Reliability Condition 3-1. Temperature Condition § Temperature Condition Test Following test are performed

8 Rev. 11©1999 - 2010 DMC Co., Ltd. 5. Handling Notes 5-1. Precautions § This product is intended for use in standard applications (computers, off

5-5. Mounting Notes § Bezel Edge Bezel edge must be positioned in the area between the Active Area and the Viewing Area. The bezel may press the to

G150XG01 V3 rev 1.0 2/28 Contents 1. Operating Precautions...

10 Rev. 11©1999 - 2010 DMC Co., Ltd. 6. Warranty 6-1. Warranty Period § The warranty period is limited to 1 year from the date of shipping. The wa

11 Rev. 11©1999 - 2010 DMC Co., Ltd. 7. Revision history Rev1 (April 15, 1998) Initial release Rev2 (June 1, 1999) The overall revision b

12 Rev. 11©1999 - 2010 DMC Co., Ltd. Rev10 (November 10, 2006) The specification item name was changed. 1-3.”Storing Temperature” to “Stora

2DI SPLAYS AND EMBEDDED SOLUTIONSDI SPLAYS AND EMBEDDED SOLUTIONSData Modul AG | Landsberger Str. 322 | 80687 Munich | Tel. +49-89-56017-0 | Fax +49-8

G150XG01 V3 rev 1.0 3/28 Record of Revision Version and Date Page Old description New Description Rev1.0 2010/11/16 First Edition

G150XG01 V3 rev 1.0 4/28 1. Operating Precautions 1) Since front polarizer is easily damaged, please be cautious and not to scratch it. 2) B

G150XG01 V3 rev 1.0 5/28 2. General Description G150XG01 V3 is a Color Active Matrix Liquid Crystal Display composed of a TFT-LCD display, a

G150XG01 V3 rev 1.0 6/28 2.2 Optical Characteristics The optical characteristics are measured under stable conditions at 25 (Room Temperature)

G150XG01 V3 rev 1.0 7/28 Note 2: Definition of 9 points position (Display active area : 304.128(H) x 228.096(V)) Note 3: The luminanc